BROWSE CATEGORIES

Fire Wolf®

Supplied by Heinrich Vorndamme.

FIRE WOLF® firefighetr clothing features a four-ply firefighter cover jacket

Order No. 1895/PBI/DEF/FW
Model 8004, EN 469:2005 Level 2


1. PBI® MATRIX, 205 g/m², yellow, antistatic
2. ISOTEMP®-TEX HY-PTFE-moisture barrier membrane
3. NOMEX®/KEVLAR®-NK-AIR heat barrier
4. Shoulder and upper arms with Spunlace insulation

Equipment characteristics:

• Cover jacket in short form with extended back bib
• Panic metal front zipper covered with cover bar
• Two inserted radio equipment pockets with lateral flap and Velcro
• Above that one microphone/ antenna holding loop each
• One cell phone pocket attached to the right radio equipment pocket
• Open slant pocket (Napoleon pocket) underneath the cover bar
• Inside pocket on the right with Velcro fastener
• Chest Velcro on the right for name tag
• Two inserted lateral pockets with flap and Velcro, underneath both pocket flaps one push button loop each for glove carabiner, on the left with one carabiner
• Vestibule in sleeves with thumb loop
• Sleeves with Velcro bar for tightening
• Elbow reinforcement made of KEVLAR®/Silicon
• Jacket border with additional suction barrier
• Revision zipper on the rear jacket border
• Velcro for one back label

Reflective Equipment:

• 3M, TRIM yellow/silver/yellow 9687 and silver 8940

1. Chest across the antenna holding loops, silver
2. Frontal across the pocket flaps, TRIM 50 mm
3. Border 2 x parallel all around, TRIM 50 mm
4. Both sleeves vertically, TRIM 50 mm and across the lower arm all around, TRIM 75 mm
5. On the back right and left vertically, TRIM 75 mm
6. Across underneath the back label, silver


Back labeling:

• Reflexite, lime/yellow, 8 x 38 cm, on Velcro, label FIRE DEPARTMENT

Sizes:

• Sizes: see page 31 = G 2

EN 469:2005, CE 0516, Z 3253/07-4339/07

A test conducted on a sensor-equipped test dummy according to

EN 469:2005 in North Carolina, USA (North Carolina State University of Textiles) confirmed the high protection level of this garment.
 
________________________________________
 
Fire Protection Equipment FIRE WOLF®

Model 8003, EN 469:2005 Level 2

Firefighter Cover Pants FIRE WOLF® three-ply

Order No. 1899/PBI/DEF/FW

1. PBI® MATRIX, 205 g/m², yellow, antistatic
2. ISOTEMP®-TEX HY-PTFE-moisture barrier membrane
3. NOMEX®/KEVLAR®-NK-AIR heat barrier

Equipment characteristics:

• High knee breeches with back bib and elastic waist
• Adjustable waist through back bar
• Elastic, removable suspenders model Hercules with with clips and bolt
• Fly with Velcro fastener
• One cargo pocket on the right, with flap and Velcro and attached knife pocket
• Knee reinforcement on the outside made of dual PAR 250 with KEVLAR®/Silicon covered with darts
• Legs of pants with width godet and Velcro bar for adjustment
• Abrasion protection godets on border made of KEVLAR®/Silicon
• 20 cm Membrane-moisture protection -sinistral- inside the legs of pants starting with border

Reflective Equipment:

• 3M, TRIM yellow/silver/yellow 9687

1. 200 mm above the borders of pants legs, 75 mm wide all around
2. Next to the side joint on the back of the pants, left and right vertically 50 cm long, 50 mm wide

• Sizes: see page 31 = G 2

EN 469:2005, CE 0516, Z 3253/07-4339/07

A test conducted on a sensor-equipped test dummy according to EN 469:2005 in North Carolina, USA (North Carolina State University of Textiles) confirmed the high protection level of this garment.

Product Image